AI coding agents (Claude Code, Codex) read, dump and run custom code on 1994 Jeep Cherokee ECU via $3 Arduino Nano
A car owner, Muhammad Zulali, documented in a YouTube video released on November 10, 2026 how Claude Code and Codex helped him read, copy and run custom code on the engine computer of his 1994 Jeep Cherokee XJ (4.0L). He used a $3 Arduino Nano, and the Jeep ultimately passed California's smog test. This is a hobbyist project, not a vulnerability disclosure or an attack. It has no CVE, no known exploitation and no threat actor. The result is self-reported and has not been independently tested. The article's security point is that agents lower the skill and time needed to reverse engineer legacy embedded systems.
Detalhes técnicos
- The ECU speaks Chrysler's slow SCI protocol at about 7,800 baud, with an inverted signal. An Arduino Nano handled the inversion (the article says the parts list came to about $15).
- Only three wires of the six-hole diagnostic plug were used. One hole carries 12 V with the key on and can destroy the board.
- Claude identified that the public ChryslerScanner parameter table did not match this Jeep. It then switched the fuel pump on, which moved the tool from read-only to control.
- Claude dumped the full ECU program. It showed a California-only fuel table that cuts fuel at the load used in the smog test, which likely explains the high NOx.
- The ECU was built about four months too early to be reflashable. Codex found a way to send a tiny program over the same three wires and run it, and then moved it into EEPROM so it survives a dead battery.
- The project is open source under GPLv3 (xj-scanner repository, tested on one vehicle only).
Remediação
No remediation applies. The article advises users of AI agents to review commands before approving them. It cites research that planted instruction files can hijack Codex and Claude Code, and an Apiiro finding that Claude Code's "don't ask again" option leaked 2,539 secrets on GitHub.
Linha do tempo
-
AI coding agents (Claude Code, Codex) read, dump and run custom code on 1994 Jeep Cherokee ECU via $3 Arduino Nano
ler a análise desta fonte ocultar
A car owner, Muhammad Zulali, documented in a YouTube video released on November 10, 2026 how Claude Code and Codex helped him read, copy and run custom code on the engine computer of his 1994 Jeep Cherokee XJ (4.0L). He used a $3 Arduino Nano, and the Jeep ultimately passed California's smog test. This is a hobbyist project, not a vulnerability disclosure or an attack. It has no CVE, no known exploitation and no threat actor. The result is self-reported and has not been independently tested. The article's security point is that agents lower the skill and time needed to reverse engineer legacy embedded systems.
Technical Details
- The ECU speaks Chrysler's slow SCI protocol at about 7,800 baud, with an inverted signal. An Arduino Nano handled the inversion (the article says the parts list came to about $15).
- Only three wires of the six-hole diagnostic plug were used. One hole carries 12 V with the key on and can destroy the board.
- Claude identified that the public ChryslerScanner parameter table did not match this Jeep. It then switched the fuel pump on, which moved the tool from read-only to control.
- Claude dumped the full ECU program. It showed a California-only fuel table that cuts fuel at the load used in the smog test, which likely explains the high NOx.
- The ECU was built about four months too early to be reflashable. Codex found a way to send a tiny program over the same three wires and run it, and then moved it into EEPROM so it survives a dead battery.
- The project is open source under GPLv3 (xj-scanner repository, tested on one vehicle only).
Remediation
No remediation applies. The article advises users of AI agents to review commands before approving them. It cites research that planted instruction files can hijack Codex and Claude Code, and an Apiiro finding that Claude Code's "don't ask again" option leaked 2,539 secrets on GitHub.